Exalto Emirates Trade Catalogue 2024

Isolators The ProSafe FS Series of FailSafe 30 and 60 Amp Galvanic Isolators will interrupt galvanic current flow with other boats at a marina when installed on a boat which is connected to AC shore power. This technology maintains AC safety ground and solves the most common forms of corrosion and premature zinc loss within a boats bonding system. The ProSafe FS Series is UL Certified to meet the parameters of the ABYC A-28 recommendation ProSafe FS installs easily and does not require a dedicated monitor to verify the operational status of the galvanic isolator as required by non FailSafe certified galvanic isolators. Both the ProSafe 30 and 60 Amp models are built on robust Flat Pack Semiconductor platforms, ensuring that in the event of a failure, the failure is safe by not compromising the ground continuity on-board when connected to AC shore power. • ABYC A-28 July ’08 Compliant and Fail Safe Certified (Certified by Underwriters Laboratories (UL). Insures shore power safety ground wire is maintained through the isolator. • Flat Pack High Power Semiconductor’s robust high power diodes allow the FS Series to meet the new FailSafe criteria for conducting inrush currents 3,000 and 5,000 Amps (FS30 and FS60 respectively) for the required duration period. • Innovative design: The FS60 will cool itself in the event it must conduct current insuring cooler operation in this mode. • Ignition protected: Meets ISO 8846 and either model can be mounted within an engine compartment. • Gold Plated Terminations: Simply install in your on board green safety ground wire (between your AC inlet and your AC Panel) to separate your D.C.bonding system from your shore A.C green wire. • ProSafe FS30 for 30 Amp Shore Cord Applications. ProSafe FS60 for (1) 50 Amp or (2) 30 Amp shore cord applications • 5 Year Warranty ProSafe FS Series Galvanic Isolator Part number 08.05.0014 08.05.0015 Model ProSafeFS30 ProSafeFS60 Shore Cord Inlet Compatibility Single 15, 16, 20 or 30 Single 50A or 2 x 30A Ratings V AC / AMPs / Hz 120/240VAC / 41A / 50 or 60 Hz 120/240VAC / 82A / 50 or 60 Hz Max Temp. 50˚ C 50˚ C Size 6.75"x7"x2.5" 7.25"x6.5"x3.75" Weight 3 lbs 3.7 lbs Part number 08.16.0168 08.16.0169 Input voltage range 6-50VDC, negative ground 6-50VDC, negative ground Number of battery banks 3 4 Maximum load current 160 amps 160amps Operating temperature -40° to +80° -40° to +80° Derate linearly from 100% @ 50%C° to 70%@80°C from 100% @ 50%C° to 70%@80°C Voltage Drop 0.6VDC @ full load 0.6VDC @ full load Dimensions - inches/mm L x W x H 8.0 x 4.5 x 2.5/ 203.2 x 114.3 x63.5 8.0 x 4.5 x 2.5/ 203.2 x 114.3 x63.5 Weight 3lb 3lb The Bocatech Automatic Power Selectors (APS) provides a simple, solid state solution for redundant DC power for vital electronic equipment while maintaining isolation of the DC power sources. The independent batteries are wired to higher torque-accepting terminals and internal diodes maintain total isolation between them. They are combined in a single output which is wired to the load. Current is automatically drawn from the battery with the higher voltage. Isolation prevents the higher-charged battery from “dumping” into the lower charged or failed battery. The unit is ruggedly constructed with heavy-duty wiring studs and epoxy potted components in an anodized aluminum case. Wiring nuts, washers and mounting screws are provided. Features • Maintains isolation of the DC power sources • Solid state • Rated for systems up to 48VDC • Higher torque-accepting stainless steel fixtures • Rugged anodized aluminum case • Designed with low voltage drop Schottky diodes Automatic power selector 08 Electrical 738